100% Original Factory Inline Filament Dryer - PET Resin Dryer/Infrared Rotary Dryer/Plastic Desiccant Dehumidifier/Plastic dryer/APET Dryer – LIANDA

We keep improving and perfecting our products and service. At the same time, we work actively to do research and development for Pet Plastic Wave Corrugated Roof Sheet Extruding Machine, Plastic Recycling Machine For Sale, Pe Head Material Shredder, Safety as a result of innovation is our promise to each other.

---

100% Original Factory Inline Filament Dryer - PET Resin Dryer/Infrared Rotary Dryer/Plastic Desiccant Dehumidifier/Plastic dryer/APET Dryer – LIANDA Detail:

Application Sample

Raw Material	PET Resin CR-BrightFor food package
Using Machine	LDHW-600*1000
Initial moisture	2210ppmTested by German Sartorius Moisture test instrument
Drying Temperature set	200℃
Drying time set	20mins
Final moisture	20ppmTested by German Sartorius Moisture test instrument
Final product	Dried PET Resin no clumping, no pellets sticking

How to Work

>>At first step, the only target is to heat up the material to a preset temperature.

Adopt relatively slow speed of drum rotating, the Infrared lamps power of the dryer will be at a higher level, then the PET pellets will have a fast heating till the temperature rises to the preset temperature.

>>Drying step

Once the material gets to the temperature, the speed of the drum will be increased to a much higher rotating speed to avoid the clumping of the material. At the same time, the infrared lamps power will be increased again to finish the drying. Then the drum rotating speed will be slowed down again. Normally the drying process will be finished after 15-20mins. (The exact time depends on the property of material)

>>After finishing the drying processing, the IR Drum will automatically discharge the material and refill the drum for the next cycle.

The automatic refilling as well as all relevant parameters for the different temperature ramps is fully integrated in the state-of-the-art Touch Screen control. Once parameters and temperature profiles are found for a specific material, theses settings can be saved as recipes in the control system.

Our Advantage

1	Low energy consumption	Significantly lower energy consumption compared to conventional processes, through the direct introduction of infrared energy to the product
2	Minutes instead of hours	The product remains for only a few minutes in the drying process and is then available for further production steps.
3	Instantly	The production run can start immediately upon startup. A warm-up phase of the machine is not required.
4	Gently	The material is heated gently from the inside to the outside and not loaded from the outside for hours with heat, and thereby possibly damaged.
5	In one step	Crystallization and drying in one step
6	Increased throughput	Increase of plant throughput by means of reduced load on extruder
7	No clumping, no sticking	The rotation of the drum ensures constant movement of the material.The spiral coils and mixing elements designed for your product ensure an optimal mix of material and avoids clumping. The product is evenly heated
8	Siemens PLC control	Control.The process data, such as material and exhaust air temperature or fill levels are continuously monitored by means of sensors and pyrometers. Deviations trigger automatic adjustment.Reproducibility.Recipes and process parameters can be stored in the controlling system to ensure optimal and reproducible results.Remote maintenance.Online service via modem.
9	Drying time only needs 20mins, final moisture can be ≤ 30ppm		The infrared rays that penetrate and reflect from the material do not affect the organization of the material, but the absorbed tissue will be converted into heat energy due to molecular excitation, which causes the temperature of the material to rise.
10	No clumping, no sticking		The rotation of the drum ensures constant movement of the material.The spiral coils and mixing elements designed for your product ensure an optimal mix of material and avoids clumping. The product is evenly heated
11	Easy clean and change material		Good access to all components allows for easy and fast cleaning.Rapid product change-over.

Machine Photos

Machine Application

Drying Drying of plastic granulates ( PET,TPE, PETG, APET, RPET, PBT, ABS/PC, HDPE, LCP, PC,PP , PVB,WPC,TPU etc) as well as other free-flowing bulk materials

Crystallization PET (Bottle flakesm granulates, sheet scrap), PET Masterbatch, CO-PET, PBT,PEEK, PLA, PPS etc

Diverse Thermal processed for removal of rest oligomeren and volatile components

Material Free Testing

Experienced engineer will make the test. Your employees are cordially invited to participate in our joint trails. Thus you have both the possibility to contribute actively and the opportunity to actually see our products in operation.

Machine Installation

>> Supply Experienced engineer to your factory to help installation and material test running

>> Adopt aviation plug, no need to connect the electrical wire while the customer get the machine in his factory. To simplify the installation step

>> Supply the operation video for installation and running guide

>>Support on line service

---

Product detail pictures:

---

Related Product Guide:

---

We try for excellence, service the customers", hopes to be the most effective cooperation workforce and dominator company for staff, suppliers and shoppers, realizes price share and ongoing marketing for 100% Original Factory Inline Filament Dryer - PET Resin Dryer/Infrared Rotary Dryer/Plastic Desiccant Dehumidifier/Plastic dryer/APET Dryer – LIANDA, The product will supply to all over the world, such as: Dominica, The Swiss, Bandung, We have established long-term, stable and good business relationships with many manufacturers and wholesalers around the world. Currently, we are looking forward to even greater cooperation with overseas customers based on mutual benefits. Please feel free to contact us for more details.